Nissan Altima 2007-2012 Service Manual: Front power window switch
Description
• BCM supplies power.
• Front power window motor RH will be operated if power window and door lock/unlock switch RH is operated.
Component Function Check
Power Window And Door Lock/unlock Switch RH
1. CHECK FRONT POWER WINDOW MOTOR RH FUNCTION
Does front power window motor RH operate with power window and door lock/unlock switch RH operation? Is the inspection result normal? YES >> Power window and door lock/unlock switch RH power supply and ground circuit are OK.
NO >> Refer to PWC-308, "FRONT POWER WINDOW SWITCH : Diagnosis Procedure".
Diagnosis Procedure
Power Window And Door Lock/unlock Switch RH Power Supply Circuit Check
1. CHECK POWER SUPPLY CIRCUIT
Check voltage between power window and door lock/unlock switch RH connector and ground.
Is the measurement value within the specification? YES >> GO TO 3
NO >> GO TO 2
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect BCM and power window and door lock/unlock switch RH.
3. Check continuity between BCM connector (A) and power window and door lock/unlock switch RH connector (B).
4. Check continuity between BCM connector (A) and ground.
Is the inspection result normal? YES >> GO TO 4
NO >> Repair or replace harness.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect power window and door lock/unlock switch RH.
3. Check continuity between power window and door lock/unlock switch RH connector and ground.
Is the inspection result normal? YES >> Replace power window and door lock/unlock switch RH.
Refer to PWC-411, "Removal and Installation". After that, refer to PWC-309, "FRONT POWER WINDOW SWITCH : Special Repair Requirement".
NO >> Repair or replace harness.
4. CHECK BCM OUTPUT SIGNAL
1. Connect BCM.
2. Turn ignition switch ON.
3. Check voltage between BCM connector and ground.
Is the measurement value within the specification? YES >> Replace power window and door lock/unlock switch RH.
Refer to PWC-411, "Removal and Installation". After that, refer to PWC-309, "FRONT POWER WINDOW SWITCH : Special Repair Requirement".
NO >> Replace BCM. Refer to BCS-96, "Removal and Installation".
Special Repair Requirement
1. PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
Refer to PWC-295, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".
Is the inspection result normal? YES >> GO TO 2
NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
2. CHECK ANTI-PINCH OPERATION
Check anti-pinch operation.
Refer to PWC-295, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".
Is the inspection result normal? YES >> Inspection end.
NO >> Refer to PWC-322, "PASSENGER SIDE : Component Function Check".
Power window main switch
Description
• BCM supplies power.
• It operates each power window motor via corresponding power window switch and
makes window move up/
down when main power window and door lock/unloc ...
Rear power window switch
Description
• BCM supplies power.
• Rear power window motor will be operated if rear power window switch is
operated. Rear power window
switch.
Component Function Check
Rear Power ...
Other materials:
Nissan vehicle immobilizer systemnats symptoms
Symptom Table
Security indicator does not turn ON or flash.
CAUTION:
• Follow Trouble Diagnosis Flowchart referring to “SEC-209, "Work Flow"”.
Determine malfunctioning
condition before performing this diagnosis.
• Check that vehicle is under the condition shown in “Con ...
Compass
Description
DESCRIPTION
With the ignition switch in the ON position, and the mode (N) switch
ON, the compass display will indicate the direction the vehicle is
heading.
Vehicle direction is displayed as follows:
• N: north
• E: east
• S: south
• W: west
ZONE VARIATION SETTING P ...
Remote starting the vehicle
perform the following:
1. Aim the Intelligent Key at the vehicle.
2. Press the LOCK button to lock
all
doors.
3. Within 5 seconds press and hold the
remote start button until the turn signal lights
illuminate. If the vehicle is not within view
press and hold the remote start
butto ...