Nissan Altima 2007-2012 Service Manual: Rear power window switch

Description

• BCM supplies power.

• Rear power window motor will be operated if rear power window switch is operated. Rear power window switch.

 Component Function Check

Rear Power Window Switch

1. CHECK REAR POWER WINDOW MOTOR FUNCTION

Does rear power window motor operate with rear power window switch operation? Is the inspection result normal? YES >> Rear power window switch power supply and ground circuit are OK.

NO >> Refer to PWC-310, "REAR POWER WINDOW SWITCH : Diagnosis Procedure".

Diagnosis Procedure

Rear Power Window Switch Power Supply Circuit Check

1. CHECK POWER SUPPLY CIRCUIT

Check voltage between rear power window switch connector and ground.

Is the measurement value within the specification? YES >> GO TO 2 (Rear power window switch LH) YES >> GO TO 3 (Rear power window switch RH) NO >> GO TO 4

2. CHECK HARNESS CONTINUITY (REAR POWER WINDOW SWITCH LH)

1. Turn ignition switch OFF.

2. Disconnect main power window and door lock/unlock switch and rear power window switch LH.

3. Check continuity between main power window and door lock/ unlock switch connector (A) and rear power window switch LH connector (B).

4. Check continuity between main power window and door lock/unlock switch connector (A) and ground.

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Repair or replace harness.

3. CHECK HARNESS CONTINUITY (REAR POWER WINDOW SWITCH RH)

1. Turn ignition switch OFF.

2. Disconnect main power window and door lock/unlock switch and rear power window switch RH.

3. Check continuity between main power window and door lock/ unlock switch connector (A) and rear power window switch RH connector (B).

4. Check continuity between main power window and door lock/unlock switch connector (A) and ground.

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Repair or replace harness.

4. CHECK HARNESS CONTINUITY

1. Disconnect BCM and rear power window switch.

2. Check continuity between BCM connector (A) and rear power window switch connector (B).

3. Check continuity between BCM connector (A) and ground.

Is the inspection result normal? YES >> GO TO 5

NO >> Repair or replace harness.

5. CHECK REAR POWER WINDOW SWITCH

Check rear power window switch.

Refer to PWC-311, "REAR POWER WINDOW SWITCH : Component Inspection".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace rear power window switch. Refer to PWC-411, "Removal and Installation".

 Component Inspection

1.CHECK REAR POWER WINDOW SWITCH

Check rear power window switch.

Is the inspection result normal? YES >> Rear power window switch is OK.

NO >> Replace rear power window switch. Refer to PWC-411, "Removal and Installation".

    Front power window switch
    Description • BCM supplies power. • Front power window motor RH will be operated if power window and door lock/unlock switch RH is operated.  Component Function Check Power Window An ...

    Power window motor
    ...

    Other materials:

    Parking/parking on hills
    WARNING ● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. ● Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park). Failure to do so could ca ...

    Front fog lamp
    Bulb Replacement REMOVAL The fog lamp is a semi-sealed beam type which uses a replaceable halogen bulb. CAUTION: • Do not touch the glass of bulb directly by hand. Keep grease and other oily substances away from it. Do not touch bulb by hand while it is lit or right after being turned ...

    BCM branch line circuit
    Diagnosis Procedure INSPECTION PROCEDURE 1.CHECK CONNECTOR 1. Turn the ignition switch OFF. 2. Disconnect the battery cable from the negative terminal. 3. Check the terminals and connectors of the BCM for damage, bend and loose connection (unit side and connector side). Is the inspec ...