Nissan Altima 2007-2012 Service Manual: B210F PNP/clutch interlock switch
Description
IPDM E/R confirms the shift position with the following signals.
• Park/neutral position (PNP) switch (CVT models) • Clutch interlock switch (M/T models) • Shift position signal from BCM (CAN)
DTC Logic
DTC DETECTION LOGIC
NOTE: • If DTC B210F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to SEC-235, "DTC Logic" • If DTC B210F is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to SEC-235, "DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions and wait for at least 1 second.
- CVT selector lever is in the P or N position
- Do not depress the brake pedal
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected? YES >> Refer to SEC-253, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure
1.INSPECTION START
Check which type of transmission the vehicle is equipped with.
Which type of transmission
CVT >> GO TO 2
M/T >> GO TO 5
2.CHECK DTC WITH BCM
Refer to BCS-91, "DTC Index".
Is the inspection result normal? YES >> GO TO 3
NO >> Repair or replace malfunctioning parts.
3.CHECK PNP SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector.
3. Turn ignition switch ON.
4. Check voltage between IPDM E/R harness connector and ground under following condition.
Is the inspection result normal? YES >> Replace IPDM E/R. Refer to PCS-48, "Removal and Installation".
NO >> (VQ35DE) GO TO 4
NO >> (QR25DE) GO TO 10
4.CHECK PNP SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect TCM harness connector.
3. Check continuity between IPDM E/R harness connector and TCM harness connector.
4. Check continuity between TCM harness connector and ground.
Is the inspection result normal? YES >> GO TO 13
NO >> Repair harness or connector.
5.CHECK CLUTCH INTERLOCK SWITCH INPUT SIGNAL (BCM)
1. Turn ignition switch OFF.
2. Disconnect BCM harness connector.
3. Check voltage between BCM harness connector and ground.
Is the inspection result normal? YES >> GO TO 6
NO >> GO TO 7
6.CHECK CLUTCH INTERLOCK SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector.
3. Turn ignition switch ON.
4. Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal? YES >> Replace the IPDM E/R. Refer to PCS-48, "Removal and Installation".
NO >> Check harness for open between clutch interlock switch and IPDM E/R.
7.CHECK CLUTCH INTERLOCK SWITCH POWER SUPPLY
1. Disconnect clutch interlock switch harness connector.
2. Check voltage between clutch interlock switch harness connector and ground.
Is the inspection result normal? YES >> GO TO 8
NO >> Check harness for open or short between clutch interlock switch and fuse.
8.CHECK CLUTCH INTERLOCK SWITCH CIRCUIT
1. Check continuity between IPDM E/R harness connector and clutch interlock switch harness connector.
2. Check continuity between clutch interlock switch harness connector and ground.
Is the inspection result normal? YES >> GO TO 9
NO >> Repair harness or connector.
NO >> Repair harness or connector.
Refer to SEC-257, "Component Inspection".
Is the inspection result normal? YES >> Replace the IPDM E/R. Refer to PCS-48, "Removal and Installation".
NO >> Replace clutch interlock switch.
10.CHECK PNP SWITCH CIRCUIT FOR CONTINUITY
1. Turn ignition switch OFF.
2. Check continuity between IPDM E/R harness connector terminals 72 and 74.
Is the inspection result normal? YES >> GO TO 11
NO >> GO TO 12
11.CHECK PNP SWITCH CIRCUIT FOR SHORT
Check continuity between IPDM E/R harness connector terminals 72, 74 and ground.
Is the inspection result normal? YES >> Replace the IPDM E/R. Refer to PCS-48, "Removal and Installation".
NO >> Repair or replace harness.
12.CHECK PNP SWITCH INPUT SIGNAL CIRCUIT
1. Disconnect PNP switch harness connector.
2. Check continuity between PNP switch and IPDM E/R harness connectors.
3. Check continuity between PNP switch harness connector and ground.
Is the inspection result normal? YES >> Replace PNP switch.
NO >> Repair harness or connector.
13.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "Intermittent Incident".
>> Inspection End.
Component Inspection
1.CHECK CLUTCH INTERLOCK SWITCH
1. Turn ignition switch OFF.
2. Disconnect clutch interlock switch harness connector.
3. Check continuity between clutch interlock switch under the following conditions.
Is the inspection result normal? YES >> Inspection End.
NO >> Replace clutch interlock switch.
B210E starter relay
Description
Located in IPDM E/R, it runs the starter motor. The starter relay is turned
ON by the BCM when the ignition
switch is in START position. IPDM E/R transmits the starter relay ON signal ...
B2110 PNP/clutch interlock switch
Description
IPDM E/R confirms the shift position with the following signals.
• Park/neutral position (PNP) switch (CVT models)
• Clutch inter lock switch (M/T models)
• Shift position sign ...
Other materials:
P1800 Vias control solenoid valve 1
Description
The VIAS control solenoid valve 1 cuts the intake manifold vacuum signal for
power valve 1 control. It
responds to ON/OFF signals from the ECM. When the solenoid is OFF, the vacuum
signal from the intake
manifold is cut. When the ECM sends an ON signal the coil pulls the plunger
...
Function information
Component Part Location
ENGINE COMPARTMENT
1. A/C compressor F3
2. Refrigerant pressure sensor E219
3. A/C relay (internal to IPDM E/R)
1. A/C compressor F3
2. Refrigerant pressure sensor E219
3. A/C relay (internal to IPDM E/R)
PASSENGER COMPARTMENT
1. Intake door motor M126
2. Fro ...
Control buttons
The control buttons for the Bluetooth® Hands-Free
Phone System are located on the steering wheel.
PHONE/SEND
Press the button to initiate a
VR
session or answer an incoming call.
You can also use the button to
interrupt the system feedback and
give a command at once. See “List o ...