Nissan Altima 2007-2012 Service Manual: P0745 line pressure solenoid valve

Description

The pressure control solenoid valve A (line pressure solenoid valve) regulates the oil pump discharge pressure to suit the driving condition in response to a signal sent from the TCM.

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

NOTE: If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.

Then wait at least 10 seconds before performing the next test.

1.CHECK DTC DETECTION

1. Turn ignition switch ON.

2. Start engine and wait at least 5 seconds.

3. Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”.

Follow the procedure “With CONSULT-III”.

Is “P0745 L/PRESS SOL/CIRC” detected? YES >> Go to TM-148, "Diagnosis Procedure".

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Diagnosis Procedure

1.CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE) CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect TCM harness connector.

3. Check resistance between TCM harness connector F16 terminal 40 and ground.

Is the inspection result normal? YES >> GO TO 5.

NO >> GO TO 2.

2.CHECK HARNESS BETWEEN TCM AND CVT UNIT [PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)] (PART 1)

1. Disconnect CVT unit connector.

2. Check continuity between TCM harness connector F16 (A) terminal 40 and CVT unit harness connector F46 (B) terminal 2.

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace damaged parts.

3.CHECK HARNESS BETWEEN TCM AND CVT UNIT [PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)] (PART 2)

Check continuity between TCM vehicle side harness connector F16 terminal 40 and ground.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace damaged parts.

4.CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)

Check pressure control solenoid valve A (line pressure solenoid valve). Refer to TM-149, "Component Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid Valve)]" Is the inspection result normal? YES >> GO TO 5.

NO >> Replace transaxle assembly. Refer to TM-259, "Exploded View".

5.DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal? YES >> Replace TCM. Refer to TM-254, "Exploded View".

NO >> Repair or replace damaged parts.

Component Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid Valve)

1.CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)

Check resistance between CVT unit terminal 2 and ground.

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace transaxle assembly. Refer to TM-259, "Exploded View".

    P0744 a/t tcc s/v function (lock -up)
    Description This malfunction is detected when the torque converter clutch does not lock-up as instructed by the TCM. This is not only caused by electrical malfunction (circuits open or shorted), ...

    P0746 pressure control solenoid A performance (line pressure solenoid valve)
    Description The pressure control solenoid valve A (line pressure solenoid valve) regulates the oil pump discharge pressure to suit the driving condition in response to a signal sent from the TCM. ...

    Other materials:

    Park/neutral position (PNP) switch
    Exploded View 1. Washer 2. Manual lever 3. PNP switch 4. CVT assembly Removal and Installation Refer to the figure for removal and installation. NOTE: • Align PNP switch position when installing. • After installation of PNP switch, check the continuity of PNP switch. • Afte ...

    Loading tips
    ● The GVW must not exceed GVWR or GAWR as specified on the F.M.V.S.S./C.M.V.S.S. certification label. ● Do not load the front and rear axle to the GAWR. Doing so will exceed the GVWR. WARNING ● Properly secure all cargo with ropes or straps to help prevent it from sliding ...

    M/T Oil
    Draining 1. Start engine and let it run to warm up transaxle oil. 2. Stop engine and remove the drain plug to drain the oil. 3. Install the drain plug with a new gasket to the transaxle case. Tighten the drain plug to the specified torque. Refer to TM-79, "Exploded View". CAUTIO ...