Nissan Altima 2007-2012 Service Manual: P0776 pressure control solenoid B performance (sec pressure solenoid valve)
Description
The pressure control solenoid valve B (secondary pressure solenoid valve) regulates the secondary pressure to suit the driving condition in response to a signal sent from the TCM.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION: Always drive vehicle at a safe speed.
NOTE: If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.CHECK DTC DETECTION
1. Turn ignition switch ON.
2. Select “DATA MONITOR”.
3. Start engine and maintain the following conditions for at least 30 consecutive seconds.
Follow the procedure “With CONSULT-III”.
Is “P0776 PRS CNT SOL/B FCTN” detected? YES >> Go to TM-152, "Diagnosis Procedure".
NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
Diagnosis Procedure
1.CHECK LINE PRESSURE
Perform line pressure test. Refer to TM-247, "Inspection and Judgment".
Is the inspection result normal? YES >> GO TO 2.
NO >> Repair or replace damaged parts. Refer to TM-247, "Inspection and Judgment".
2.CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
1. Turn ignition switch OFF.
2. Disconnect CVT unit harness connector.
3. Check pressure control solenoid valve B (secondary pressure solenoid valve). Refer to TM-153, "Component Inspection [Pressure Control Solenoid Valve B (Secondary Pressure Solenoid Valve)]".
Is the inspection result normal? YES >> GO TO 3.
NO >> Replace transaxle assembly. Refer to TM-447, "Exploded View".
3.CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)
Check pressure control solenoid valve A (line pressure solenoid valve). Refer to TM-153, "Component Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid Valve)]".
Is the inspection result normal? YES >> GO TO 4.
NO >> Replace transaxle assembly. Refer to TM-259, "Exploded View".
4.CHECK TRANSMISSION FLUID PRESSURE SENSOR A (SECONDARY PRESSURE SENSOR) SYSTEM
Check transmission fluid pressure sensor A (secondary pressure sensor) system. Refer to TM-160, "DTC Logic".
Is the inspection result normal? YES >> GO TO 5.
NO >> Repair or replace damaged parts.
5.DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal? YES >> Replace TCM. Refer to TM-254, "Exploded View".
NO >> Repair or replace damaged parts.
Component Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid Valve)
1.CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)
Check resistance between CVT unit terminal 2 and ground.
Is the inspection result normal? YES >> INSPECTION END
NO >> Replace transaxle assembly. Refer to TM-259, "Exploded View".
Component Inspection [Pressure Control Solenoid Valve B (Secondary Pressure Solenoid Valve)
1.CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
Check resistance between CVT unit terminal 3 and ground.
Is the inspection result normal? YES >> INSPECTION END
NO >> Replace transaxle assembly. Refer to TM-259, "Exploded View".
P0746 pressure control solenoid A
performance (line pressure solenoid
valve)
Description
The pressure control solenoid valve A (line pressure solenoid valve)
regulates the oil pump discharge pressure
to suit the driving condition in response to a signal sent from the TCM.
...
P0778 pressure control solenoid B
electrical (sec pressure solenoid
valve)
Description
The pressure control solenoid valve B (secondary pressure solenoid valve)
regulates the oil pump discharge
pressure to suit the driving condition in response to a signal sent from the ...
Other materials:
How to park with predicted course lines
WARNING
● Always turn and check that it is safe to
do so before backing up. Always back
up slowly.
● Use the displayed lines as a reference.
The lines are highly affected by the number
of occupants, fuel level, vehicle position,
road conditions and road grade.
● If the ti ...
Consult-iii checking system
Description
• When CONSULT-III is connected with a data link connector
equipped on the vehicle side, it will communicate with the control
unit equipped in the vehicle and then enable various kinds of diagnostic
tests.
1 : Hood release handle
2 : Data link connector
• Refer to “CONSU ...
ECM branch line circuit
Diagnosis Procedure
INSPECTION PROCEDURE
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the following terminals and connectors for damage, bend and loose
connection (unit side and connector
side).
- ECM
- Harnes ...