Nissan Altima 2007-2012 Service Manual: B261A push-button ignition switch
Description
IPDM E/R transmits the push-button ignition switch status via CAN communication to BCM. BCM receives push-button ignition switch status by hardwire input. BCM compares the 2 signals for mismatch.
DTC Logic
DTC DETECTION LOGIC
NOTE: • If DTC B261A is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to SEC-235, "DTC Logic".
• If DTC B261A is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to SEC-236, "DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Press the push-button ignition switch under the following conditions and wait for at least 1 second.
- CVT selector lever is in the P position
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected? YES >> Refer to SEC-307, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure
1.CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL 1
1. Turn ignition switch OFF.
2. Disconnect push-button ignition switch harness connector and IPDM E/R harness connector.
3. Check voltage between push-button ignition switch harness connector and ground.
Is the inspection result normal? YES >> GO TO 4
NO >> GO TO 2
2.CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT
1. Disconnect BCM harness connector.
2. Check continuity between push-button ignition switch harness connector M38 (A) terminal 4 and BCM harness connector M19 (B) terminal 77.
3. Check continuity between push-button ignition switch harness connector M38 (A) terminal 4 and ground.
Is the inspection result normal? YES >> GO TO 3
NO >> Repair harness or connector.
3.CHECK PUSH-BUTTON IGNITION SWITCH
1. Disconnect IPDM E/R harness connector.
2. Check continuity between push-button ignition switch harness connector M38 (A) terminal 4 and IPDM E/R harness connector E18 (B) terminal 28.
3. Check continuity between push-button ignition switch harness connector and ground.
Is the inspection result normal? YES >> GO TO 4
NO >> Repair harness or connector.
4.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "Intermittent Incident".
>> Inspection End.
B2619 BCM
Description
BCM requests IPDM E/R to supply power to steering lock unit. After receiving
the power, the steering lock unit
transmits an ON signal to BCM.
DTC Logic
DTC DETECTION LOGIC
DTC CON ...
B26E1 No reception of engine status
signal
Description
BCM receives the engine status signal from ECM via CAN communication.
DTC Logic
DTC DETECTION LOGIC
NOTE:
• If DTC B26E1 is displayed with DTC U1000, first perform the trouble diag ...
Other materials:
Seat belts
The seat belts can be cleaned by wiping them
with a sponge dampened in a mild soap solution.
Allow the belts to dry completely in the shade
before using them. See “Seat belt maintenance”
in the “Safety – Seats, seat belts and supplemental
restraint system” section of this manual.
W ...
Audio system (coupe)
System Diagram
System Description
AUDIO SYSTEM
The audio system consists of the following components
• Audio unit
• Window antenna
• Steering wheel audio control switches
• Door speakers
• Front tweeters
• Rear speakers
When the audio system is on, radio signals are receive ...
Clutch pedal
Exploded View
1. Clutch pedal assembly
2. Clutch interlock switch
3. ASCD clutch switch
4. Lock nut
Removal and Installation
REMOVAL
1. Disconnect master cylinder rod end from clutch pedal lever.
2. Disconnect the ASCD clutch switch and clutch interlock switch
harness connectors.
3. ...