Nissan Altima 2007-2012 Service Manual: Front power window switch

Description

Main power window and door lock/unlock switch, power window and door lock/unlock switch RH and BCM transmit and receive the signal by power window serial link.

The signal mentioned below is transmitted from BCM to main power window and door lock/unlock switch and power window and door lock/unlock switch RH

• Keyless power window down signal

The signal mentioned below is transmitted from main power window and door lock/unlock switch to power window and door lock/unlock switch RH

• Front door window RH operation signal

• Power window control by key cylinder switch signal

• Retained power operation signal

• Power window lock switch signal

Component Function Check

1. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH OUTPUT SIGNAL

Check (“CDL LOCK SW ”, “CDL UNLOCK SW”) in “DATA MONITOR” mode for “POWER DOOR LOCK SYSTEM” with CONSULT-III. Refer to BCS-19, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)".

Is the inspection result normal? YES >> Power window serial link is OK.

NO >> Refer to PWC-333, "FRONT POWER WINDOW SWITCH : Diagnosis Procedure".

 Diagnosis Procedure

Power Window Serial Link Check

1. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH

1. Remove Intelligent Key, and close the front door LH and RH.

2. Check signal between BCM connector and ground with oscilloscope when door lock and unlock switch (LH and RH) is turned to “LOCK” or “UNLOCK”.

3. Check that signals which are shown in the figure below can be detected during 10 second just after door lock and unlock switch (LH and RH) is turned to “LOCK” or “UNLOCK”.

Is the inspection result normal? YES >> Power window serial link is OK.

NO >> GO TO 2

2. CHECK POWER WINDOW SERIAL LINK CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM.

3. Check continuity between BCM connector (A) and power window and door lock/unlock switch RH connector (B).

4. Check continuity between BCM connector (A) and ground.

Is the inspection result normal? YES >> Replace main power window and door lock/unlock switch. Refer to PWC-411, "Removal and Installation". After that, refer to PWC-307, "POWER WINDOW MAIN SWITCH : Special Repair Requirement".

NO >> Repair or replace harness.

    Power window main switch
    Description Main power window and door lock/unlock switch, power window and door lock/unlock switch RH and BCM transmit and receive the signal by power window serial link. The signal mentioned ...

    Power window lock switch
    Description Ground circuit of main power window and door lock/unlock switch shuts off if power window lock switch of main power window and door lock/unlock switch is operated. This inhibits all ...

    Other materials:

    Auto operation does not operate but manual operates normally (driver side)
    Diagnosis Procedure 1. PERFORM INITIALIZATION PROCEDURE Perform initialization procedure. Refer to PWC-21, "POWER WINDOW MAIN SWITCH : Special Repair Requirement". Is the inspection result normal? YES >> GO TO 2 NO >> Repair or replace the malfunctioning parts. 2. CH ...

    Headlining
    Exploded View 1. Headlining assembly (without sunroof) 2. Assist grip 3. Headlining assembly (with sunroof) 4. Front room/Map lamp assembly bracket 5. Front room/Map lamp assembly 6. Sunvisor 7. Sunvisor holder 8. Sunvisor cover A. Clip C101 B. Dual lock fastener Removal and Install ...

    Air cleaner filter
     Removal and Installation 1. Air duct hose 2. Duct sub-cover 3. Front air duct 4. Air cleaner case (lower) 5. Grommets 6. Air cleaner case mounting bracket 7. Bracket 8. Air cleaner filter 9. Air cleaner case (upper) 10. Mass air flow sensor A. To electric throttle control actuator ...