Nissan Altima 2007-2012 Service Manual: Front wiper does not operate

Description

The front wiper does not operate under any operation conditions

Diagnosis Procedure

1. CHECK WIPER RELAY OPERATION

1. Start IPDM E/R auto active test. Refer to PCS-14, "Diagnosis Description".

2. Check that the front wiper operates at the LO/HI operation.

1. Select "FRONT WIPER" of IPDM E/R active test item.

2. While operating the test item, check that front wiper LO/HI operation and OFF.

Does the front wiper operate? YES >> GO TO 5

NO >> GO TO 2

2. CHECK FRONT WIPER MOTOR FUSE

1. Turn the ignition switch OFF.

2. Check that the front wiper motor fuse 30A (No. 55, located in the IPDM E/R) is not blown.

Is the fuse blown? YES >> Replace the fuse after repairing the affected circuit.

NO >> GO TO 3

3. CHECK FRONT WIPER MOTOR (GND) OPEN CIRCUIT

1. Turn the ignition switch OFF.

2. Disconnect front wiper motor.

3. Check continuity between front wiper motor harness connector and ground.

Does continuity exist? YES >> GO TO 4

NO >> Repair or replace harness.

4. CHECK FRONT WIPER MOTOR OUTPUT VOLTAGE

1. Turn the ignition switch OFF.

2. Turn the ignition switch ON.

3. Select "FRONT WIPER" of IPDM E/R active test item.

4. With operating the test item, check voltage between IPDM E/R harness connector and ground.

Is the measurement normal? YES LO circuit>>Refer to WW-20, "Diagnosis Procedure".

YES HI circuit>>Refer to WW-22, "Diagnosis Procedure".

NO >> Replace IPDM E/R. Refer to PCS-48, "Removal and Installation".

5. CHECK FRONT WIPER REQUEST SIGNAL INPUT

1. Select "FR WIP REQ" of IPDM E/R "DATA MONITOR" item.

2. Switch the front wiper switch to HI and LO.

3. With operating the front wiper switch, check the monitor status.

Is the status of item normal? YES >> Replace IPDM E/R. Refer to PCS-48, "Removal and Installation".

NO >> GO TO 6

6. CHECK COMBINATION SWITCH

1. Perform the inspection of the combination switch. Refer to BCS-10, "System Description".

Is combination switch normal? YES >> Replace BCM. Refer to BCS-96, "Removal and Installation".

NO >> Repair or replace the malfunctioning parts.

    Front wiper and washer system symptoms
    Symptom Table CAUTION: Perform the self-diagnosis with CONSULT-III before performing the diagnosis by symptom. Perform the diagnosis by DTC if DTC is detected. ...

    Normal operating condition
    Description FRONT WIPER MOTOR PROTECTION FUNCTION • IPDM E/R may stop the front wiper to protect the front wiper motor if any obstruction (operation resistance) such as a large amount of snow i ...

    Other materials:

    Power window system
    System Diagram FRONT POWER WINDOW LH ANTI-PINCH SYSTEM System Description MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH INPUT/OUTPUT SIGNAL CHART POWER WINDOW OPERATION • Power window system is operable during the retained power operation timer after turning ignition switch ON and O ...

    IPDM-E branch line circuit
    Diagnosis Procedure INSPECTION PROCEDURE 1.CHECK CONNECTOR 1. Turn the ignition switch OFF. 2. Disconnect the battery cable from the negative terminal. 3. Check the terminals and connectors of the IPDM E/R for damage, bend and loose connection (unit side and connector side). Is the in ...

    B261a push-button ignition switch
    Description IPDM E/R transmits the push-button ignition switch status via CAN communication to BCM. BCM receives push-button ignition switch status by hardwire input. BCM compares the 2 signals for mismatch. DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B261A is displayed with DTC U1000 ...