Nissan Altima 2007-2012 Service Manual: Hands free phone system (sedan)

System Diagram

System Description

Refer to the owner's manual for Bluetooth telephone system operating instructions.

NOTE: Cellular telephones must have their wireless connection set up (paired) before using the Bluetooth telephone system.

Bluetooth telephone system allows users who have a Bluetooth cellular telephone to make a wireless connection between their cellular telephone and the Bluetooth control unit. Hands-free cellular telephone calls can be sent and received. Personal memos can be created using the Nissan Voice Recognition system. Some Bluetooth cellular telephones may not be recognized by the Bluetooth control unit. When a cellular telephone or the Bluetooth control unit is replaced, the telephone must be paired with the Bluetooth control unit. Different cellular telephones may have different pairing procedures. Refer to the cellular telephone operating manual.

BLUETOOTH CONTROL UNIT

When the ignition switch is turned to ACC or ON, the Bluetooth control unit will power up. During power up, the Bluetooth control unit is initialized and performs various self checks. Initialization may take up to 10 seconds.

If a phone is present in the vehicle and paired with the Bluetooth control unit, Nissan Voice Recognition will then become active. Bluetooth telephone functions can be turned off using the Nissan Voice Recognition system.

STEERING WHEEL AUDIO CONTROL SWITCHES

When buttons on the steering wheel audio control switch are pushed, the resistance in steering wheel audio control switch circuit changes depending on which button is pushed. The Bluetooth control unit uses this signal to perform various functions while navigating through the voice recognition system.

The following functions can be performed using the steering wheel audio control switch: • Initiate Self Diagnosis of the Bluetooth telephone system

• Start a voice recognition session

• Answer and end telephone calls

• Adjust the volume of calls

• Record memos

MICROPHONE

The microphone is located in the roof console assembly. The microphone sends a signal to the Bluetooth control unit. The microphone can be actively tested during self-diagnosis.

AUDIO UNIT

The audio unit receives signals from the Bluetooth control unit and sends audio signals to the speakers.

Component Parts Location

1. Tweeter LH M51

2. Steering wheel audio control switches

3. Tweeter RH M52

4. Audio unit M43, M44, M45, M81

5. Center speaker M151

6. Combination meter M24

7. Front door speaker

LH D3

RH D103

8. Rear subwoofer LH B120

9. Rear subwoofer RH B124

10. Rear door speaker

LH D202

RH D302

11. Antenna amp. M502

12. Satellite radio tuner B123, B129

13. Bluetooth control unit B125, B126

14. BOSE speaker amp. B121, B122

15. Microphone R7

Component Description

    Hands free phone system (coupe)
    System Diagram System Description Refer to the owner's manual for Bluetooth telephone system operating instructions. NOTE: Cellular telephones must have their wireless connection set up (pa ...

    Diagnosis system (audio unit)
    Diagnosis Description Self-diagnosis mode can check the following items. • Audio unit hardware/software versions • Continuity of each speaker channel • Continuity of each audio unit switc ...

    Other materials:

    Key cylinder switch
    Description For vehicles equipped with LH and RH anti-pinch system, the main power window and door lock/unlock switch detects condition of the door key cylinder switch and transmits to BCM as the LOCK or UNLOCK signal. For vehicles equipped with LH anti-pinch system only, the front door loc ...

    Headlamp (HI) circuit
    Description The IPDM E/R (intelligent power distribution module engine room) controls the headlamp high relay based on inputs from the BCM over the CAN communication lines. When the headlamp high relay is energized, power flows through fuses 48 and 49, located in the IPDM E/R. Power then flo ...

    Anti-pinch system does not operate normally (driver side)
    Diagnosis Procedure 1. PERFORM INITIALIZATION PROCEDURE Perform initialization procedure. Refer to PWC-21, "POWER WINDOW MAIN SWITCH : Special Repair Requirement". Is the inspection result normal? YES >> GO TO 2 NO >> Repair or replace the malfunctioning parts. 2. C ...