Nissan Altima 2007-2012 Service Manual: Intake door motor
Description
SYSTEM DESCRIPTION
Component Parts
Intake door control system components are: • Front air control
• Intake door motor (LCU)
System Operation
The intake door control determines the intake door position based on the position of the recirculation switch.
When the recirculation switch is depressed the intake door motor rotates closing off the fresh air inlet and recirculating the cabin air. If the recirculation switch is depressed again, the intake door motor rotates in the opposite direction, again allowing fresh air into the cabin.
COMPONENT DESCRIPTION
Intake Door Motor
The intake door motor (1) is attached to the blower unit. It rotates so that air is drawn from inlets set by the front air control. Motor rotation is conveyed to a lever which activates the intake door.
Diagnosis Procedure
SYMPTOM: • Intake door does not change.
• Intake door motor does not operate normally.
INSPECTION FLOW
1. CONFIRM SYMPTOM BY PERFORMING OPERATION CHECK - REC (
)
1. Press the vent mode.( ).
2. Press REC ( ) switch. The REC
(
) indicator should illumination.
3. Press REC ( ) switch again. The
REC (
) indicator should go out.
4. Listen for intake door position change (you should sound change slightly).
Can a symptom be duplicated? YES >> GO TO 3
NO >> GO TO 2
2. PERFORM COMPLETE OPERATIONAL CHECK
Perform a complete operational check and check for any symptoms. Refer to HAC-102, "Operational Check".
Is the inspection result normal? YES >> Refer to HAC-155, "Symptom Matrix Chart".
NO >> System OK.
3. CHECK FOR SERVICE BULLETINS
Check for any service bulletins.
>> GO TO 4
4. CHECK INTAKE DOOR MOTOR OPERATION
Check and verify intake door mechanism for smooth operation.
Is the inspection result normal? YES >> GO TO 5
NO >> Repair as necessary.
5. CHECK LAN SYSTEM CIRCUIT
Perform diagnostic procedure for the LAN system. Refer to HAC-115, "Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 6
NO >> Repair as necessary.
6. CHECK AIR MIX DOOR MOTORS PBR CIRCUIT
Perform diagnostic procedure for the air mix door motor. Refer to HAC-122, "Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 7
NO >> Repair as necessary.
7. RECHECK FOR SYMPTOMS
Perform a complete operational check and check for any symptoms. Refer to HAC-102, "Operational Check".
Does another symptom exist? YES >> Repair as necessary.
NO >> Replace front air control. Refer to VTL-8, "Removal and Installation".
DIAGNOSIS PROCEDURE FOR INTAKE DOOR MOTOR
SYMPTOM: Intake door motor does not operate normally.
Perform diagnosis procedure. Refer to HAC-115, "Diagnosis Procedure".
Air mix door motor
Description
SYSTEM DESCRIPTION
Component Parts
Air mix door control system components are:
• Front air control
• Air mix door motor (LCU)
System Operation
The front air control receives use ...
Blower motor
Description
SYSTEM DESCRIPTION
Component Parts
Fan speed control system components are:
• Front air control
• A/C LAN system (PBR built-in mode door motor, air mix door motor and intake
do ...
Other materials:
P0452 evap control system pressure
sensor
Description
The EVAP control system pressure sensor detects pressure in the
purge line. The sensor output voltage to the ECM increases as pressure
increases.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously condu ...
General maintenance
During the normal day-to-day operation of the
vehicle, general maintenance should be performed
regularly as prescribed in this section. If
you detect any unusual sounds, vibrations or
smells, be sure to check for the cause or have a
NISSAN dealer do it promptly. In addition, you
should notify ...
Foreword
Welcome to the growing family of new NISSAN
owners. This vehicle is delivered to you with
confidence. It was produced using the latest
techniques and strict quality control.
This manual was prepared to help you understand
the operation and maintenance of your
vehicle so that you may enjoy ma ...