Nissan Altima 2007-2012 Service Manual: Intake sensor

Description

Intake Sensor

The intake sensor is located on the heater and cooling unit. It converts temperature of air after it passes through the evaporator into a resistance value which is then input to the front air control.

Diagnosis Procedure

SYMPTOM: Intake sensor circuit is open or shorted.

1.CHECK VOLTAGE BETWEEN INTAKE SENSOR HARNESS CONNECTOR AND BODY GROUND

1. Disconnect intake sensor connector M69.

2. Press ignition switch ON.

3. Check voltage between intake sensor connector M69 terminal 1 and ground.

Is the inspection result normal? YES >> GO TO 2

NO >> GO TO 4

2.CHECK INTAKE SENSOR GROUND CIRCUIT BETWEEN INTAKE SENSOR AND FRONT AIR CONTROL

1. Press ignition switch OFF.

2. Disconnect front air control connector M37.

3. Check continuity between front air control connector M37 (A) terminal 26 and intake sensor harness connector M69 (B) terminal 4.

If OK, check harness for short.

Is the inspection result normal? YES >> GO TO 3

NO >> Repair harness or connector.

3.CHECK INTAKE SENSOR

Check intake sensor. Refer to HAC-59, "Diagnosis Procedure".

Is the inspection result normal? YES >> 1. Replace front air control. Refer to VTL-8, "Removal and Installation".

2. Confirm system operation.

NO >> 1. Replace intake sensor. Refer to VTL-11, "Removal and Installation".

2. Confirm system operation.

4.CHECK INTAKE SENSOR CIRCUIT BETWEEN INTAKE SENSOR AND FRONT AIR CONTROL

1. Press ignition switch OFF.

2. Disconnect front air control connector M37.

3. Check continuity between front air control connector M37 (A) terminal 25 and intake sensor harness connector M69 (B) terminal 1.

If OK, check harness for short.

Is the inspection result normal? YES >> 1. Replace front air control, Refer to VTL-8, "Removal and Installation".

2. Confirm system operation.

NO >> Repair harness or connector.

Component Inspection

Intake Sensor

After disconnecting intake sensor harness connector, measure resistance between terminals 1 and 2 at sensor harness side, using the table below.

If NG, replace intake sensor. Refer to VTL-11, "Removal and Installation".

    Sunload sensor
    Description COMPONENT DESCRIPTION The sunload sensor (1) is located on the LH tweeter grille. It detects sunload entering through windshield by means of a photo diode. The sensor converts the sunl ...

    Power supply and ground circuit for front air control
    Description COMPONENT DESCRIPTION FRONT AIR CONTROL The front air control has a built-in microcomputer which processes information sent from various sensors needed for air conditioner operation. ...

    Other materials:

    Rear seat belt
    Exploded View 1. Seat belt retractor RH 2. Seat belt buckle RH 3. Seat belt buckle center 4. Seat belt buckle LH 5. Seat belt retractor center 6. Seat belt retractor LH A. Retractor anchor bolt B. Outer anchor bolt C. Buckle anchor bolt 1. Seat belt retractor outer RH 2. Seat belt buc ...

    Precaution
    Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the dr ...

    Front bumper
    Removal and Installation 1. Front bumper supports 2. Front bumper reinforcement 3. Energy absorbing foam 4. Tow cover 5. Front grille 6. Engine under cover 7. Fog lamp finisher (if equipped) 8. Fog lamp (if equipped) 9. Front bumper fascia REMOVAL 1. Remove the front fender protecto ...