Nissan Altima 2007-2012 Service Manual: P0840 transmission fluid pressure sensor A (sec pressure sensor)

Description

The transmission fluid pressure sensor A (secondary pressure sensor) detects secondary pressure of CVT and sends TCM the signal.

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

NOTE: If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.

Then wait at least 10 seconds before performing the next test.

1.CHECK DTC DETECTION

1. Turn ignition switch ON.

2. Select “DATA MONITOR”.

3. Make sure that output voltage of CVT fluid temperature sensor is within the range below.

ATF TEMP SEN : 1.0 – 2.0 V

If out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage (cool down the fluid)

4. Start engine and wait for at least 5 consecutive seconds.

Follow the procedure “With CONSULT-III”.

Is “P0840 TR PRS SENS/A CIRC” detected? YES >> Go to TM-341, "Diagnosis Procedure".

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Diagnosis Procedure

1.CHECK INPUT SIGNAL

1. Start engine.

2. Check voltage between TCM harness connector F16 terminal 15 and ground.

3. Turn ignition switch OFF.

Is the inspection result normal? YES >> GO TO 8.

NO >> GO TO 2.

2.CHECK POWER AND SENSOR GROUND

1. Turn ignition switch ON.

2. Check voltage between TCM harness connector F16 terminals 25 and 26.

Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 5.

3.CHECK HARNESS BETWEEN TCM AND CVT UNIT [TRANSMISSION FLUID PRESSURE SENSOR A (SECONDARY PRESSURE SENSOR)] (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM harness connector and CVT unit connector .

3. Check continuity between TCM harness connector F16 (A) terminal 15 and CVT unit harness connector F46 (B) terminal 23.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace damaged parts.

4.CHECK HARNESS BETWEEN TCM AND CVT UNIT [TRANSMISSION FLUID PRESSURE SENSOR A (SECONDARY PRESSURE SENSOR)] (PART 2)

Check continuity between TCM harness connector F16 terminal 15 and ground.

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace damaged parts.

5. CHECK HARNESS BETWEEN TCM AND CVT UNIT (SENSOR POWER AND SENSOR GROUND) (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM connector and CVT unit connector.

3. Check continuity between TCM harness connector F16 (A) terminals 25, 26 and CVT unit harness connector F46 (B) terminals 19, 20.

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace damaged parts.

6.CHECK HARNESS BETWEEN TCM AND CVT UNIT (SENSOR POWER AND SENSOR GROUND) (PART 2)

Check continuity between TCM harness connector F16 terminals 25, 26 and ground.

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace damaged parts.

7.CHECK TCM

1. Replace same type TCM. Refer to TM-430, "Removal and Installation".

2. Connect each connector.

3. Perform “DTC CONFIRMATION PROCEDURE”. Refer to TM-341, "DTC Logic".

Is “P0840 TR PRS SENS/A CIRC” detected? YES (Only DTC P0840 detected)>>Replace control valve. Refer to TM-447, "Exploded View".

YES (DTC P0840 and except DTC P0840 are detected)>>Replace transaxle assembly. Refer to TM-447, "Removal and Installation".

NO >> Replace TCM. Refer to TM-430, "Removal and Installation".

8.DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal? YES >> Replace TCM. Refer to TM-430, "Removal and Installation".

NO >> Repair or replace damaged parts.

    P0826 manual mode switch
    Description Manual mode switch is installed in shift control device. The manual mode switch sends shift up and shift down switch signals to TCM with CAN communication. TCM sends the switch sig ...

    P0841 pressure sensor function
    Description Using the engine load (throttle position), the primary pulley revolution speed, and the secondary pulley revolution speed as input signal, TCM changes the operating pressure of the pri ...

    Other materials:

    NISSAN Intelligent Key® operation
    You can lock or unlock the doors without taking the key out of your pocket or bag. When you carry the Intelligent Key with you, you can lock or unlock all doors by pushing the door handle request switch within the range of operation. Locking doors 1. Move the shift lever to the P (Park) ...

    How to select piston and bearing
    DESCRIPTION *For the service parts, the grade for fitting cannot be selected between a piston pin and a connecting rod. (Only 0 grade is available.) The information at the shipment from the plant is described as a reference. • The identification grade stamped on each part is the grade ...

    P0031, P0032 A/F Sensor 1 heater
    Description SYSTEM DESCRIPTION The ECM performs ON/OFF duty control of the A/F sensor 1 heater corresponding to the engine operating condition to keep the temperature of A/F sensor 1 element at the specified range. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITI ...