Nissan Altima 2007-2012 Service Manual: Passenger side
Description
• BCM supplies power.
• Power window motor RH will be operated if power window and door lock/unlock switch RH is operated.
Component Function Check
Power Window And Door Lock/Unlock Switch RH
1. CHECK POWER WINDOW MOTOR RH FUNCTION
Does power window motor RH operate with power window and door lock/unlock switch RH operation? Is the inspection result normal? YES >> Power window and door lock/unlock switch RH power supply and ground circuit are OK.
NO >> Refer to PWC-200, "PASSENGER SIDE : Diagnosis Procedure".
Diagnosis Procedure
Power Window And Door Lock/Unlock Switch RH Power Supply Circuit Check
1. CHECK POWER SUPPLY CIRCUIT
Check voltage between power window and door lock/unlock switch RH connector and ground.
Is the measurement value within the specification? YES >> GO TO 3
NO >> GO TO 2
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect BCM and power window and door lock/unlock switch RH.
3. Check continuity between BCM connector (A) and power window and door lock/unlock switch RH connector (B).
4. Check continuity between BCM connector (A) and ground.
Is the inspection result normal? YES >> GO TO 4
NO >> Repair or replace harness.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect power window and door lock/unlock switch RH.
3. Check continuity between power window and door lock/unlock switch RH connector and ground.
Is the inspection result normal? YES >> Replace power window and door lock/unlock switch RH.
Refer to PWC-291, "Removal and Installation". After that, refer to PWC-201, "PASSENGER SIDE : Special Repair Requirement".
NO >> Repair or replace harness.
4. CHECK BCM OUTPUT SIGNAL
1. Connect BCM.
2. Turn ignition switch ON.
3. Check voltage between BCM connector and ground.
Is the measurement value within the specification? YES >> Replace power window and door lock/unlock switch RH.
Refer to PWC-291, "Removal and Installation". After that, refer to PWC-201, "PASSENGER SIDE : Special Repair Requirement".
NO >> Replace BCM. Refer to BCS-96, "Removal and Installation".
Special Repair Requirement
1. PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
Refer to PWC-190, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".
Is the inspection result normal? YES >> GO TO 2
NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
2. CHECK ANTI-PINCH OPERATION
Check anti-pinch operation.
Refer to PWC-190, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".
Is the inspection result normal? YES >> Inspection end.
NO >> Refer to PWC-208, "PASSENGER SIDE : Component Function Check".
Power window main switch
Description
• BCM supplies power.
• It operates each power window motor via corresponding power window switch and
makes window move up/
down when main power window and door lock/unlock swi ...
Other materials:
ECM branch line circuit
Diagnosis Procedure
INSPECTION PROCEDURE
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the following terminals and connectors for damage, bend and loose
connection (unit side and connector
side).
- ECM
- Harnes ...
AV Control unit (coupe)
Reference Value
VALUES ON THE DIAGNOSIS TOOL
CONSULT-III data monitor item
TERMINAL LAYOUT
PHYSICAL VALUES
Wiring Diagram
DTC Index
...
Front wiper blade
Removal and Installation
REMOVAL
1. Lift the front wiper arm and wiper blade assembly away from the
windshield.
2. Rotate the front wiper blade assembly and push the release tab
(A), then move the front wiper blade assembly down (B) the
front wiper arm.
3. Remove the front wiper blade as ...