Nissan Altima 2007-2012 Service Manual: Power supply and ground circuit for front air control
Description
FRONT AIR CONTROL
The front air control has a built-in microcomputer which processes information sent from temperature control dial and various switches needed for air conditioner operation. The air mix door motor, mode door motor, intake door motor, blower motor and compressor are then controlled.
POTENTIO TEMPERATURE CONTROL (PTC)
The PTC is built into the front air control.
Component Function Check
COMPONENT INSPECTION
SYMPTOM: A/C system does not come on.
INSPECTION FLOW
1. CONFIRM SYMPTOM BY PERFORMING OPERATION CHECK
1. Press A/C switch (indicator should illuminate).
2. Confirm that the compressor clutch engages (sound or visual inspection).
Can a symptom be duplicated? YES >> GO TO 3
NO >> GO TO 2
2. PERFORM COMPLETE OPERATIONAL CHECK
Perform a complete operational check and check for any symptoms. Refer to HAC-102, "Operational Check".
Is the inspection result normal? YES >> Refer to HAC-155, "Symptom Matrix Chart".
NO >> System OK.
3. CHECK FOR SERVICE BULLETINS
Check for any service bulletins.
>> GO TO 4
4. CHECK MAIN POWER SUPPLY AND GROUND CIRCUIT
Check main power supply and ground circuit. Refer to HAC-135, "Diagnosis Procedure".
Is the inspection result normal? YES >> Replace front air control. Refer to VTL-8, "Removal and Installation".
NO >> Repair as necessary.
Diagnosis Procedure
DIAGNOSIS PROCEDURE FOR A/C SYSTEM
SYMPTOM: A/C system does not come on.
1.CHECK POWER SUPPLY CIRCUIT FOR FRONT AIR CONTROL
1. Disconnect front air control connector M37.
2. Press ignition switch ON.
3. Check voltage between front air control connector M37 terminals 39 and 40, and ground.
Is the inspection result normal? YES >> GO TO 2
NO >> Check the following.
• 10A fuses [Nos. 6, and 3, located in the fuse block (J/B)].
• If fuses are OK, check for open circuit in wiring harness. Repair or replace as necessary.
• If fuses are NG, replace fuse and check wiring harness for short circuit. Repair or replace as necessary.
2.CHECK BODY GROUND CIRCUIT FOR FRONT AIR CONTROL
1. Press ignition switch OFF.
2. Check continuity between front air control connector M37 terminals 17and 37 and ground.
Is the inspection result normal? YES >> • Replace front air control. Refer to VTL-8, "Removal and Installation".
• Inspection End.
NO >> Repair or replace harness.
Magnet clutch
Component Function Check
INSPECTION FLOW
1. CONFIRM SYMPTOM BY PERFORMING OPERATION CHECK - MAGNET CLUTCH
1. Press ignition switch ON.
2. Press vent switch ( ).
3. Press A/C switch.
4. C ...
ECU diagnosis
AIR CONDITIONER CONTROL
Reference Value
VALUES ON THE DIAGNOSIS TOOL
TERMINAL LAYOUT
PHYSICAL VALUES
Wiring Diagram - Air Conditioner Control (Manual)
- Coupe
Wiring D ...
Other materials:
Magnet clutch
Description
SYSTEM DESCRIPTION
Front air control controls A/C compressor operation by ambient temperature
and signal from ECM.
Low Temperature Protection Control
Front air control will turn the A/C compressor ON or OFF as determined
by a signal detected by ambient sensor.
When ambient te ...
IPDM-E branch line circuit
Diagnosis Procedure
INSPECTION PROCEDURE
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the IPDM E/R for damage, bend and loose
connection (unit side
and connector side).
Is the in ...
Audio system (coupe)
System Diagram
System Description
AUDIO SYSTEM
The audio system consists of the following components
• Audio unit
• BOSE speaker amp.
• Window antenna
• Steering wheel audio control switches
• Door speakers
• Front tweeters
• Center speaker
• Rear tweeters
• Rear sub ...