Nissan Altima 2007-2012 Service Manual: Sound signal circuit (sedan)

SATELLITE RADIO TUNER

 Description

Left and right channel audio signals are supplied from the satellite radio tuner to the audio unit through the sound signal circuits.

Diagnosis Procedure

LEFT CHANNEL

1.CHECK HARNESS

1. Turn ignition switch OFF.

2. Disconnect satellite radio tuner (factory installed) connector B123 and audio unit connector M45.

3. Check continuity between satellite radio tuner (factory installed) connector B123 (A) and audio unit connector M45 (B).


4. Check continuity between satellite radio tuner (factory installed)


4. Check continuity between satellite radio tuner (factory installed) connector B123 (A) and ground.

Are continuity results as specified?


Are continuity results as specified? YES >> GO TO 2

NO >> Repair harness or connector.

2.CHECK LEFT CHANNEL AUDIO SIGNAL

1. Connect satellite radio tuner (factory installed) and audio unit.

2. Turn ignition switch ON.

3. Check signal between satellite radio tuner (factory installed) connector B123 terminals 21 and 22 with CONSULT-III or oscilloscope.



Are voltage readings as specified?


Are voltage readings as specified? YES >> Replace audio unit. Refer to AV-215, "Removal and Installation".

NO >> Replace satellite radio tuner. Refer to AV-223, "Removal and Installation - Sedan".

RIGHT CHANNEL

1.CHECK HARNESS

1. Turn ignition switch OFF.

2. Disconnect satellite radio tuner (factory installed) connector B123 and audio unit connector M45.

3. Check continuity between satellite radio tuner (factory installed) connector B123 (A) and audio unit connector M45 (B).


4. Check continuity between satellite radio tuner (factory installed)


4. Check continuity between satellite radio tuner (factory installed) connector B123 (A) and ground.

Are continuity results as specified?


Are continuity results as specified? YES >> GO TO 2

NO >> Repair harness or connector.

2.CHECK RIGHT CHANNEL AUDIO SIGNAL

1. Connect satellite radio tuner (factory installed) and audio unit.

2. Turn ignition switch ON.

3. Check signal between satellite radio tuner (factory installed) connector B123 terminals 23 and 24 with CONSULT-III or oscilloscope.



Are voltage readings as specified?


Are voltage readings as specified? YES >> Replace audio unit. Refer to AV-215, "Removal and Installation".

NO >> Replace satellite radio tuner. Refer to AV-223, "Removal and Installation - Sedan".

    Sound signal circuit (coupe)
    SATELLITE RADIO TUNER Description Left and right channel audio signals are supplied from the satellite radio tuner to the audio unit through the sound signal circuits. Diagnosis Procedure LEF ...

    Microphone signal circuit (coupe)
    Description Voice signals are transmitted from the microphone to the Bluetooth control unit using the microphone signal circuits. Diagnosis Procedure 1.CHECK HARNESS BETWEEN BLUETOOTH CONTROL U ...

    Other materials:

    Vehicle recovery (freeing a stuck vehicle)
    Pulling a stuck vehicle WARNING To avoid vehicle damage, serious personal injury or death when recovering a stuck vehicle: ● Contact a professional towing service to recover the vehicle if you have any questions regarding the recovery procedure. ● Do not use the vehicle tie-down ...

    P0447 evap canister vent control valve
    Description The EVAP canister vent control valve is located on the EVAP canister and is used to seal the canister vent. This solenoid valve responds to signals from the ECM. When the ECM sends an ON signal, the coil in the solenoid valve is energized. A plunger will then move to seal the ca ...

    On-vehicle repair
    INSTRUMENT PANEL ASSEMBLY Exploded View 1. Center speaker grille 2. Tweeter speaker grille (LH) 3. Instrument panel 4. Instrument side mask (LH) 5. Combination meter 6. Lower knee protector (LH) 7. Cluster lid A 8. Instrument lower cover (LH) 9. Fuse block cover 10. Steering column cov ...