Nissan Altima 2007-2012 Service Manual: B2190, P1610 nats antenna AMP
Description
Performs ID verification through BCM and Intelligent Key when push-button ignition switch is pressed.
Prohibits the release of steering lock or start of engine when an unregistered ID of Intelligent Key is used.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Insert Intelligent Key into the key slot.
2. Check “Self Diagnostic Result” with CONSULT-III.
Is DTC detected? YES >> Refer to SEC-263, "Diagnosis Procedure".
NO >> GO TO 2
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Press the push-button ignition switch.
2. Check “Self Diagnostic Result” with CONSULT-III.
Is DTC detected? YES >> Refer to SEC-263, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure
1. INSPECTION START
Check the case in which DTC is detected.
• Case1: It is detected when Intelligent Key is inserted into key slot.
• Case2: It is detected after Intelligent Key is inserted into key slot and push-button ignition switch is pressed.
In which case is DTC detected? Case1. >> GO TO 2
Case2. >> GO TO 4
2.CHECK KEY SLOT INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect key slot harness connector.
3. Check voltage between key slot harness connector and ground.
Is the inspection result normal? YES >> Replace key slot. Refer to SEC-409, "Removal and Installation".
NO >> GO TO 3
3.CHECK KEY SLOT CIRCUIT
1. Disconnect BCM harness connector.
2. Check continuity between key slot harness connector M40 (A) terminal 2 and BCM harness connector M19 (B) terminal 68.
3. Check continuity between key slot harness connector M40 (A) terminal 2 and ground.
Is the inspection result normal? YES >> GO TO 8
NO >> Repair harness or connector.
4.CHECK PUSH-IGNITION SWITCH OPERATION
Press push-button ignition switch and check if it turns ON.
Does ignition switch turn to ON? YES >> GO TO 5
NO >> GO TO 7
5.CHECK KEY SLOT COMMUNICATION SIGNAL
1. Turn ignition switch OFF.
2. Disconnect key slot harness connector.
3. Check voltage between key slot harness connector and ground.
Is the inspection result normal? YES >> Replace key slot. Refer to SEC-409, "Removal and Installation".
NO >> GO TO 6
6.CHECK KEY SLOT COMMUNICATION SIGNAL CIRCUIT
1. Disconnect BCM harness connector.
2. Check continuity between key slot harness connector M40 (A) terminal 3 and BCM harness connector M19 (B) terminal 69.
3. Check continuity between key slot harness connector M40 (A) terminal 3 and ground.
Is the inspection result normal? YES >> GO TO 8
NO >> Repair harness or connector.
7.CHECK KEY SLOT GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect key slot harness connector.
3. Check continuity between key slot harness connector and ground.
Is the inspection result normal? YES >> GO TO 8
NO >> Repair harness or connector.
8.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "Intermittent Incident".
>> Inspection End.
B2110 PNP/clutch interlock switch
Description
IPDM E/R confirms the shift position with the following signals.
• Park/neutral position (PNP) switch (CVT models)
• Clutch inter lock switch (M/T models)
• Shift position sign ...
B2191, P1615 difference of key
Description
Performs ID verification through BCM and Intelligent Key when push-button
ignition switch is pressed.
Prohibits the release of steering lock or start of engine when an unregistered ...
Other materials:
B2606 steering lock relay
Description
The steering lock relay ON signal is transmitted to IPDM E/R by BCM via CAN
communication.
IPDM E/R turns the steering lock relay ON and transmits the release of the
steering to BCM.
DTC Logic
DTC DETECTION LOGIC
NOTE:
• If DTC B2606 is displayed with DTC U1000, first per ...
U120C DVD-ROM mecha detect
Description
Refer to AV-240, "System Description".
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK DVD-ROM
Check DVD-ROM for dirt, scratches and warpage.
Is the DVD-ROM clean and undamaged?
YES >> Replace AV control unit. Refer to AV-437, "Removal and I ...
Anti-pinch system does not operate
normally (driver side)
Diagnosis Procedure
1. PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
Refer to PWC-21, "POWER WINDOW MAIN SWITCH : Special Repair Requirement".
Is the inspection result normal?
YES >> GO TO 2
NO >> Repair or replace the malfunctioning parts.
2. C ...