Nissan Altima 2007-2012 Service Manual: B2110 PNP/clutch interlock switch
Description
IPDM E/R confirms the shift position with the following signals.
• Park/neutral position (PNP) switch (CVT models) • Clutch inter lock switch (M/T models) • Shift position signal from BCM (CAN)
DTC Logic
DTC DETECTION LOGIC
NOTE: • If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to SEC-235, "DTC Logic".
• If DTC B2110 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to SEC-236, "DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the ignition switch ON under the following conditions and wait for at least 1 second.
- CVT selector lever is in the P or N position
- Do not depress the brake pedal
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected? YES >> Refer to SEC-258, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure
1.INSPECTION START
Check which type of transmission the vehicle is equipped with.
Which type of transmission
CVT >> GO TO 2
M/T >> GO TO 5
2.CHECK DTC WITH BCM
Refer to BCS-91, "DTC Index".
Is the inspection result normal? YES >> GO TO 3
NO >> Repair or replace malfunctioning parts.
3.CHECK PNP SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector.
3. Turn ignition switch ON.
4. Check voltage between IPDM E/R harness connector and ground under following condition.
Is the inspection result normal? YES >> Replace IPDM E/R. Refer to PCS-48, "Removal and Installation".
NO >> (VQ35DE) GO TO 4
NO >> (QR25DE) GO TO 10
4.CHECK PNP SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect TCM harness connector.
3. Check continuity between IPDM E/R harness connector and TCM harness connector.
4. Check continuity between TCM harness connector and ground.
Is the inspection result normal? YES >> GO TO 13
NO >> Repair harness or connector.
5.CHECK CLUTCH INTERLOCK SWITCH INPUT SIGNAL (BCM)
1. Turn ignition switch OFF.
2. Disconnect BCM harness connector.
3. Check voltage between BCM harness connector and ground.
Is the inspection result normal? YES >> GO TO 6
NO >> GO TO 7
6.CHECK CLUTCH INTERLOCK SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector.
3. Turn ignition switch ON.
4. Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal? YES >> Replace the IPDM E/R. Refer to PCS-48, "Removal and Installation".
NO >> Check harness for open between clutch interlock switch and IPDM E/R.
7.CHECK CLUTCH INTERLOCK SWITCH POWER SUPPLY
1. Disconnect clutch interlock switch harness connector.
2. Check voltage between clutch interlock switch harness connector and ground.
Is the inspection result normal? YES >> GO TO 8
NO >> Check harness for open or short between clutch interlock switch and fuse.
8.CHECK CLUTCH INTERLOCK SWITCH CIRCUIT
1. Check continuity between IPDM E/R harness connector and clutch interlock switch harness connector.
2. Check continuity between clutch interlock switch harness connector and ground.
Is the inspection result normal? YES >> GO TO 9
NO >> Repair harness or connector.
9.CHECK CLUTCH INTERLOCK SWITCH
Refer to SEC-262, "Component Inspection".
Is the inspection result normal? YES >> Replace the IPDM E/R. Refer to PCS-48, "Removal and Installation".
NO >> Replace clutch interlock switch.
10.CHECK PNP SWITCH CIRCUIT FOR CONTINUITY
1. Turn ignition switch OFF.
2. Check continuity between IPDM E/R harness connector terminals 72 and 74.
Is the inspection result normal? YES >> GO TO 11
NO >> GO TO 12
11.CHECK PNP SWITCH CIRCUIT FOR SHORT
Check continuity between IPDM E/R harness connector terminals 72, 74 and ground.
Is the inspection result normal? YES >> Replace the IPDM E/R. Refer to PCS-48, "Removal and Installation".
NO >> Repair or replace harness.
12.CHECK PNP SWITCH INPUT SIGNAL CIRCUIT
1. Disconnect PNP switch harness connector.
2. Check continuity between PNP switch and IPDM E/R harness connectors.
3. Check continuity between PNP switch harness connector and ground.
Is the inspection result normal? YES >> Replace PNP switch.
NO >> Repair harness or connector.
13.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "Intermittent Incident".
>> Inspection End.
Component Inspection
1.CHECK CLUTCH INTERLOCK SWITCH
1. Turn ignition switch OFF.
2. Disconnect clutch interlock switch harness connector.
3. Check continuity between clutch interlock switch under the following conditions.
Is the inspection result normal? YES >> Inspection End.
NO >> Replace clutch interlock switch.
B210F PNP/clutch interlock switch
Description
IPDM E/R confirms the shift position with the following signals.
• Park/neutral position (PNP) switch (CVT models)
• Clutch interlock switch (M/T models)
• Shift position sign ...
B2190, P1610 nats antenna AMP
Description
Performs ID verification through BCM and Intelligent Key when push-button
ignition switch is pressed.
Prohibits the release of steering lock or start of engine when an unregistered
...
Other materials:
Tire Pressure Monitoring System (TPMS)
This vehicle is equipped with the Tire Pressure
Monitoring System (TPMS). It monitors tire pressure
of all tires except the spare. When the low
tire pressure warning light is lit, and the “Tire
Pressure Low - Add Air” warning appears in the
vehicle information display, one or more of your
...
Basic inspection
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
OVERALL SEQUENCE
DETAILED FLOW
1. GET INFORMATION FOR SYMPTOM
Get the detailed information from the customer about the symptom (the
condition and the environment when
the incident/malfunction occurred).
>> GO TO 2
2. CHECK DTC
1. Check DTC ...
P0643 Sensor power supply
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform
the following before conducting
the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
...