Nissan Altima 2007-2012 Service Manual: Communication signal circuit (sedan) satellite radio tuner

 Description

Communication signals are exchanged between the audio unit and satellite radio tuner using the communication circuits.

 Diagnosis Procedure

1.CHECK HARNESS - 1

1. Turn ignition switch OFF.

2. Disconnect satellite radio tuner (factory installed) connector B123 and audio unit connector M45.

3. Check continuity between satellite radio tuner (factory installed) harness connector B123 (A) terminal 28 and audio unit harness connector M45 (B) terminal 38.

4. Check continuity between satellite radio tuner (factory installed) harness connector B123 (A) terminal 28 and ground.

Are continuity results as specified? YES >> GO TO 2

NO >> Repair harness or connector.

2.CHECK HARNESS - 2

1. Check continuity between satellite radio tuner (factory installed) harness connector B123 (A) terminal 29 and audio unit harness connector M45 (B) terminal 39.

2. Check continuity between satellite radio tuner (factory installed) harness connector B123 (A) terminal 29 and ground.

Are continuity results as specified? YES >> GO TO 3

NO >> Repair harness or connector.

3.CHECK HARNESS - 3

1. Check continuity between satellite radio tuner (factory installed) harness connector B123 (A) terminal 30 and audio unit harness connector M45 (B) terminal 40.

2. Check continuity between satellite radio tuner (factory installed) harness connector B123 (A) terminal 30 and ground.

Are continuity results as specified? YES >> GO TO 4

NO >> Repair harness or connector.

4.CHECK REQ1 SIGNAL

1. Connect satellite radio tuner (factory installed) connector and audio unit connector.

2. Turn ignition switch to ACC 3. Check signal between satellite radio tuner (factory installed) harness connector B123 terminal 28 and ground with CONSULT-III or oscilloscope.

Are voltage readings as specified? YES >> GO TO 5

NO >> Replace audio unit. Refer to AV-215, "Removal and Installation".

5.CHECK TXD SIGNAL

Check signal between satellite radio tuner (factory installed) harness connector B123 terminal 29 and ground with CONSULT-III or oscilloscope.

Are the voltage readings as specified? YES >> GO TO 6

NO >> Replace satellite radio tuner. Refer to AV-223, "Removal and Installation - Sedan".

6.CHECK RXD SIGNAL

Check signal between satellite radio tuner (factory installed) harness connector B123 terminal 30 and ground with CONSULT-III or oscilloscope.

Are the voltage readings as specified? YES >> Replace satellite radio tuner. Refer to AV-223, "Removal and Installation - Sedan".

NO >> Replace audio unit. Refer to AV-215, "Removal and Installation".

    Satellite radio tuner
    Description Communication signals are exchanged between the audio unit and satellite radio tuner using the communication circuits. Diagnosis Procedure 1.CHECK HARNESS - 1 . Turn ignition switc ...

    Sound signal circuit (coupe)
    SATELLITE RADIO TUNER Description Left and right channel audio signals are supplied from the satellite radio tuner to the audio unit through the sound signal circuits. Diagnosis Procedure LEF ...

    Other materials:

    Main line between dlc and abs circuit
    Diagnosis Procedure INSPECTION PROCEDURE 1.CHECK CONNECTOR 1. Turn the ignition switch OFF. 2. Disconnect the battery cable from the negative terminal. 3. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side). - Harness co ...

    Key cylinder switch
    Description For vehicles equipped with LH and RH anti-pinch system, the main power window and door lock/unlock switch detects condition of the door key cylinder switch and transmits to BCM as the LOCK or UNLOCK signal. For vehicles equipped with LH anti-pinch system only, the door lock ass ...

    Evaporative emission system
    System Diagram EVAPORATIVE EMISSION LINE DRAWING 1. Intake manifold collector 2. EVAP service port 3. EVAP canister purge volume control solenoid valve A. From next figure 1. EVAP control system pressure sensor 2. EVAP canister vent control valve 3. EVAP canister A. To previous figu ...