Nissan Altima 2007-2012 Service Manual: Front wiper blade refill

 Removal and Installation

REMOVAL

1. Remove the front wiper blade. Refer to WW-115, "FRONT WIPER BLADE : Removal and Installation".

2. Hold the wiper blade refill lip at the end (A) of the front wiper blade (1) with a suitable tool (B) as shown, and pull it firmly in the direction (C).

• U clip (part of the front wiper blade assembly) (D)

• If the wiper blade refill lip is torn due to wear, insert a suitable tool (A) into the space between the end of the wiper blade refill (1) and the front wiper blade (2) and pull the wiper blade refill (1) out as shown.

INSTALLATION

1. If the rib (A) has become detached from the wiper blade refill (1), check that the curve of the rib (A) is in the same direction as the curve of the wiper blade refill (1) and insert the rib (A) into the slit (B) in the wiper blade refill (1) as shown.

• If the rib (A) has a notch (B), insert the rib (A) into the wiper blade refill (1) so the notch (B) fits over the protrusion (C) in the wiper blade refill (1) as shown.

2. Insert the wiper blade refill (1) tip into the end of the front wiper blade (2) in the direction (C). Push the wiper blade refill (1) in while pressing it into the end of the front wiper blade (2) as shown. After the wiper blade refill is fully inserted, remove the holder (B).

• Tab [part of front wiper blade (2)] (A)

• Make sure to slide the refill into the front wiper blade so that the wiper blade refill is held by the tabs (A) on the front wiper blade as shown.

3. Push the wiper blade refill (1) until the tabs on the front wiper blade (2) fit into the stoppers (A) in the end of the wiper blade refill (1). Make sure the LOCK mark (B) on the wiper blade refill (1) is aligned with the lock point symbol (C) on the front wiper blade (2) as shown.

4. Before installing the front wiper blade assembly, make sure that the wiper blade refill (1) end is fully covered by the front wiper blade (2) in area (A) as shown.

5. Install the front wiper blade. Refer to WW-115, "FRONT WIPER BLADE : Removal and Installation".

    Front wiper
    Exploded View 1. Rib (part of wiper blade refill) 2. Wiper blade refill 3. Front RH wiper blade assembly (includes wiper blade refill) 4. Front RH wiper arm 5. Wiper arm cap 6. Front wiper d ...

    Front wiper blade
    Removal and Installation REMOVAL 1. Lift the front wiper arm and wiper blade assembly away from the windshield. 2. Rotate the front wiper blade assembly and push the release tab (A), then move ...

    Other materials:

    P0452 Evap control system pressure sensor
    Description The EVAP control system pressure sensor detects pressure in the purge line. The sensor output voltage to the ECM increases as pressure increases. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If DTC Confirmation Procedure has been previously condu ...

    The low washer fluid warning continues displaying, or does not display
    Description • The warning is still displayed even after washer fluid is added. • The warning is not displayed even though the washer tank is empty. Diagnosis Procedure 1.CHECK WASHER LEVEL SWITCH SIGNAL CIRCUIT Check the washer level switch signal circuit. Refer to MWI-51, "Diagnosi ...

    Headlining
    Exploded View 1. Room/Map lamp assembly 2. Mirror harness cover 3. Sunvisor holder 4. Sunvisor 5. Sunvisor cover 6. Headlining assembly (without sunroof) 7. Headlining assembly (with sunroof) 8. Rear assist grip 9. Front assist grip 10. Sunroof clip A. Metal clip B. Dual lock fastene ...