Nissan Altima 2007-2012 Service Manual: Passenger side

 Description

Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch or power window and door lock/unlock switch RH.

Component Function Check

1. CHECK POWER WINDOW MOTOR CIRCIUT

Does power window motor operate with operating main power window and door lock/unlock switch or power window and door lock/unlock switch RH? Is the inspection result normal? YES >> Power window motor RH is OK.

NO >> Refer to PWC-204, "PASSENGER SIDE : Diagnosis Procedure".

 Diagnosis Procedure

Power Window Motor RH Circuit Check

1. CHECK POWER WINDOW SWITCH RH OUTPUT SIGNAL

1. Disconnect power window motor RH.

2. Turn ignition switch ON.

3. Check voltage between power window motor RH connector and ground.

Is the measurement value within the specification? YES >> GO TO 2

NO >> Replace power window and door lock/unlock switch RH. Refer to PWC-291, "Removal and Installation".

After that, refer to PWC-201, "PASSENGER SIDE : Special Repair Requirement".

2. CHECK HARNESS CONTINUITY

1. Turn ignition switch OFF.

2. Disconnect power window and door lock/unlock switch RH.

3. Check continuity between power window and door lock/unlock switch RH connector (A) and power window motor RH connector (B).

4. Check continuity between power window and door lock/unlock switch RH connector (A) and ground.

Is the inspection result normal? YES >> GO TO 3

NO >> Repair or replace harness.

3. CHECK POWER WINDOW MOTOR RH

Check power window motor RH.

Refer to PWC-205, "PASSENGER SIDE : Component Inspection".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace power window motor RH. Refer to GW-19, "Removal and Installation". After that, refer to PWC-205, "PASSENGER SIDE : Special Repair Requirement".

Component Inspection

1. CHECK POWER WINDOW MOTOR RH

Does motor operate by connecting the battery voltage directly to power window motor RH?

Is the inspection result normal? YES >> Power window motor RH is OK.

NO >> Replace power window motor RH. Refer to GW-19, "Removal and Installation". After that, refer to PWC-205, "PASSENGER SIDE : Special Repair Requirement".

Special Repair Requirement

1. PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure.

Refer to PWC-190, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".

Is the inspection result normal? YES >> GO TO 2

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

2. CHECK ANTI-PINCH OPERATION

Check anti-pinch operation.

Refer to PWC-190, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".

Is the inspection result normal? YES >> Inspection End.

NO >> Refer to PWC-208, "PASSENGER SIDE : Component Function Check".

    Driver side
    Description Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch. Component Function Check 1. CHECK POWER WINDOW MOTOR CIRCUIT Does power window ...

    Encoder
    ...

    Other materials:

    BCM branch line circuit
    Diagnosis Procedure INSPECTION PROCEDURE 1.CHECK CONNECTOR 1. Turn the ignition switch OFF. 2. Disconnect the battery cable from the negative terminal. 3. Check the terminals and connectors of the BCM for damage, bend and loose connection (unit side and connector side). Is the inspec ...

    Seat belt, buckles, retractors, anchors and adjusters
    Inspection CAUTION: • After any collision, inspect all seat belt assemblies, including retractors and other attached hardwares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in use during a collision, unless not damaged and properly operating afte ...

    Steering wheel
    Removal and Installation REMOVAL NOTE: When reconnecting spiral cable, fix cable with a tape so that fixing case and rotating part keep aligned. This will omit neutral position alignment procedure during spiral cable installation. 1. Set vehicle to the straight-ahead position. 2. Remove ...