Nissan Altima 2007-2012 Service Manual: Passenger side
Description
Detects condition of the power window motor RH operation and transmits to power window and door lock/ unlock switch RH as pulse signal.
Component Function Check
1. CHECK ENCODER OPERATION
Does door glass RH perform AUTO open/close operation normally when operating power window and door lock/unlock switch RH? Is the inspection result normal? YES >> Encoder operation is OK.
NO >> Refer to PWC-209, "PASSENGER SIDE : Diagnosis Procedure".
Diagnosis Procedure
1. CHECK ENCODER SIGNAL
1. Turn ignition switch ON.
2. Check signal between power window and door lock/unlock switch RH connector and ground with oscilloscope.
Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> GO TO 2
2. CHECK POWER WINDOW MOTOR RH POWER SUPPLY
1. Turn ignition switch ON.
2. Check voltage between power window motor RH connector and ground.
Is the measurement value within the specification? YES >> GO TO 4
NO >> GO TO 3
3. CHECK HARNESS CONTINUITY 1
1. Turn ignition switch OFF.
2. Disconnect power window and door lock/unlock switch RH and power window motor RH.
3. Check continuity between power window and door lock/unlock switch RH connector (A) and power window motor RH connector (B).
4. Check continuity between power window and door lock/unlock switch RH connector (A) and ground.
Is the inspection result normal? YES >> Replace power window and door lock/unlock switch RH. Refer to PWC-291, "Removal and Installation".
After that, refer to PWC-201, "PASSENGER SIDE : Special Repair Requirement".
NO >> Repair or replace harness.
4. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect power window motor RH.
3. Check continuity between power window motor RH connector and ground.
Is the inspection result normal? YES >> GO TO 6
NO >> GO TO 5
5. CHECK HARNESS CONTINUITY 2
1. Disconnect power window and door lock/unlock switch RH.
2. Check continuity between power window and door lock/unlock switch RH connector (A) and power window motor RH connector (B).
Is the inspection result normal? YES >> Replace power window and door lock/unlock switch RH.
Refer to PWC-291, "Removal and Installation". After that, refer to PWC-201, "PASSENGER SIDE : Special Repair Requirement".
NO >> Repair or replace harness.
6. CHECK HARNESS CONTINUITY 3
1. Disconnect power window and door lock/unlock switch RH.
2. Check continuity between power window and door lock/unlock switch RH connector (A) and power window motor RH connector (B).
3. Check continuity between power window and door lock/unlock switch RH connector (A) and ground.
Is the inspection result normal? YES >> Replace power window motor RH. Refer to GW-19, "Removal and Installation". After that, refer to PWC-205, "PASSENGER SIDE : Special Repair Requirement".
NO >> Repair or replace harness.
Driver side
Description
Detects condition of the power window motor LH operation and transmits to
main power window and door
lock/unlock switch as pulse signal.
Component Function Check
1. CHECK ENCO ...
Door switch
Description
Detects door open/close condition and transmits the signal to BCM.
Component Function Check
1. CHECK DOOR SWITCH INPUT SIGNAL
Check (“DOOR SW-DR” and “DOOR SW-AS”) in “DATA ...
Other materials:
Tire Pressure Monitoring System (TPMS)
Each tire, including the spare (if provided),
should be checked monthly when cold and inflated
to the inflation pressure recommended by
the vehicle manufacturer on the vehicle placard
or tire inflation pressure label. (If your vehicle has
tires of a different size than the size indicated on
th ...
BCM (Body control module)
Reference Value
VALUES ON THE DIAGNOSIS TOOL
Terminal Layout
Physical Values
1: Sedan only
2: With LH front window anti-pinch
3: With LH and RH front window anti-pinch
4: With Intelligent Key
5: Without Intelligent Key
Wiring Diagram-Coupe
...
BCM branch line circuit
Diagnosis Procedure
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the BCM for damage, bend and loose
connection (unit side and
connector side).
Is the inspection result normal?
Y ...