Nissan Altima 2007-2012 Service Manual: Power window system

System Diagram

FRONT POWER WINDOW LH ANTI-PINCH SYSTEM

System Description

MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH INPUT/OUTPUT SIGNAL CHART

POWER WINDOW OPERATION

• Power window system is operable during the retained power operation timer after turning ignition switch ON and OFF.

• Main power window and door lock/unlock switch can open/close all windows.

• Front & rear power window switches can open/close the corresponding windows.

POWER WINDOW AUTO-OPERATION (FRONT LH)

• AUTO UP/DOWN operation can be performed when main power window and door lock/unlock switch turns to AUTO.

• Encoder continues detecting the movement of power window motor and transmits to main power window and door lock/unlock switch as the encoder pulse signal while power window motor is operating.

• Main power window and door lock/unlock switch reads the changes of encoder signal and stops AUTO operation when door glass is at fully opened/closed position.

• Power window motor is operable in case encoder is malfunctioning.

RETAINED POWER OPERATION

• Retained power operation is an additional power supply function that enables power window system to operate during the 45 seconds even when ignition switch is turned OFF

Retained power function cancel conditions

• Front door CLOSE (door switch OFF)→OPEN (door switch ON).

• When ignition switch is ON.

• When timer time passes. (45 seconds)

POWER WINDOW LOCK

Ground circuit inside main power window and door lock/unlock switch shuts off when power window lock switch is ON. This inhibits power window switch operation except with the main power window and door lock/ unlock switch.

ANTI-PINCH OPERATION (FRONT LH)

• Pinch foreign material in the door glass during AUTO-UP operation,and it is the anti-pinch function that lowers the door glass 150 mm or 2 seconds when detected.

• Encoder continues detecting the movement of power window motor and transmits to main power window and door lock/unlock switch as the encoder pulse signal while power window motor is operating.

• Resistance is applied to the power window motor rotation that changes the frequency of encoder pulse signal if foreign material is trapped in the door glass.

• Power window switch controls to lower the window glass for 150 mm or 2 seconds after it detects encoder pulse signal frequency change.

OPERATION CONDITION

• When door glass AUTO-UP operation is performed (anti-pinch function does not operate just before the door glass closes and is fully closed) NOTE: Depending on environment and driving conditions, if a similar impact or load is applied to the door glass, it may lower.

Component Parts Location

1. BCM M16, M17, M18, M19

2. Front power window motor LH D9, RH D104

3. Rear power window motor LH D204, RH D304

4. Main power window and door lock/ unlock switch D7, D8

5. Power window and door lock/unlock switch RH D105

6. Rear power window switch LH D203, RH D303

7. Front door switch LH B8, RH B108

Component Description

FRONT POWER WINDOW LH ANTI-PINCH SYSTEM

    Other materials:

    U1208 DVD-ROM comm
    Description Refer to AV-240, "System Description". DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.CHECK DVD-ROM Check DVD-ROM for dirt, scratches and warpage. Is the DVD-ROM clean and undamaged? OK >> Replace AV control unit. Refer to AV-437, "Removal and Insta ...

    Normal operating condition
    Description FUEL CUT CONTROL (AT NO LOAD AND HIGH ENGINE SPEED) If the engine speed is above 1,800 rpm under no load (for example, the selector lever position is neutral and engine speed is over 1,800 rpm) fuel will be cut off after some time. The exact time when the fuel is cut off varies b ...

    ECU diagnosis
    BCM (BODY CONTROL MODULE) Reference Value VALUES ON THE DIAGNOSIS TOOL Terminal Layout Physical Values 1: Sedan only 2: With LH front window anti-pinch 3: With LH and RH front window anti-pinch Wiring Diagram - TIRE PRESSURE MONITORING SYSTEM ...