Nissan Altima Owners Manual: Text messaging

WARNING

● Laws in some jurisdictions may restrict the use of some of the applications and features, such as social networking and texting.

● Laws in some jurisdictions may restrict the use of “Text-to-Speech”. Check local regulations before using this feature.

● Use the text messaging feature after stopping your vehicle in a safe location.

If you have to use the feature while driving, exercise extreme caution at all times so full attention may be given to vehicle operation.

● If you are unable to devote full attention to vehicle operation while using the text messaging feature, pull off the road to a safe location and stop your vehicle.

NOTE:

This feature is automatically disabled if the connected device does not support the Message Access Profile (MAP). See the phone’s Owner’s Manual for details and instructions.

The system allows for the sending and receiving of text messages through the vehicle interface.

Sending a text message:

1. Press the 2. Say “Messaging”. button.


2. Say “Messaging”.

3. Say “Send Text”.

4. The system will provide a list of available commands in order to determine the recipient of the text message. Choose from the following:

● (A name)
● Number
● Incoming Calls
● Outgoing Calls
● Missed Calls

If “Incoming Calls”, “Outgoing Calls”, or “Missed Calls” is selected, the following additional commands will be displayed:

● Send Text
● Next Entry
● Previous Entry

For more information about these options, see “Voice commands” in this section.

5. Once a recipient is chosen, the system prompts for which message to send. Five predefined messages are available as well as three custom messages. To choose one of the predefined messages, speak one of the following:

● “Driving, can’t text” ● “Call me”
● “On my way”
● “Running late”
● “Okay”

To send one of the custom messages, say “Custom Message”. If more than one custom message is stored, the system will prompt for the number of the desired custom message. For more information on setting and managing custom text messages, see “Bluetooth® settings” in this section.

Reading a received text message:

1. Press the 2. Say “Messaging”. button.


2. Say “Messaging”.

3. Say “Read Text”.

The text message, sender and delivery time are shown on the screen. Use the tuning switch on the steering wheel to scroll through all text messages if more than one are available. Press the message screen. button to exit the text
message screen.

Press the following button to access the
following options for replying to the text message: ● Call Back
Speak this command to call the sender of the text message using the Bluetooth® Hands-Free Phone System.

● Send Text
Speak this command to send a text message response to the sender of the text message.

● Read Text
Speak this command to read the text message again.

● Previous Text
Speak this command to move to the previous text message (if available).

● Next Text
Speak this command to move to the next text message (if available).

NOTE:

Text messages are only displayed if the vehicle speed is less than 5 mph (8 km/h).

    Ending a call
    To end an active call, press the button. ...

    Bluetooth® settings
    To access and adjust the settings for the Bluetooth® Hands-Free Phone System: 1. Press the SETTING button. 2. Use the TUNE/SCROLL knob to select “Bluetooth” and then press the ENTER button: ...

    Other materials:

    Rear regulator
    Exploded View 1. Rear door 2. Door glass run 3. Door glass 4. Inside seal 5. Partition sash 6. Rear window seal 7. Door rear, glass 8. Regulator assembly 9. Window motor 10. Water shield Removal and Installation REMOVAL 1. Remove the rear door finisher. Refer to INT-34, "Removal ...

    Rapid air pressure loss
    Rapid air pressure loss or a “blow-out” can occur if the tire is punctured or is damaged due to hitting a curb or pothole. Rapid air pressure loss can also be caused by driving on under-inflated tires. Rapid air pressure loss can affect the handling and stability of the vehicle, especial ...

    BCM branch line circuit
    Diagnosis Procedure 1.CHECK CONNECTOR 1. Turn the ignition switch OFF. 2. Disconnect the battery cable from the negative terminal. 3. Check the terminals and connectors of the BCM for damage, bend and loose connection (unit side and connector side). Is the inspection result normal? Y ...