Nissan Altima 2007-2012 Service Manual: Component diagnosis
- Trouble diagnosis - specification value
- Power supply and ground circuit
- U0101 Can comm circuit
- U0140 Can comm circuit
- U1001 Can comm circuit
- P0011 IVT Control
- P0031, P0032 A/F Sensor 1 heater
- P0037, P0038 HO2S2 Heater
- P0075 ivt control solenoid valve
- P0101 maf sensor
- P0102, p0103 maf sensor
- P0112, p0113 iat sensor
- P0116 ect sensor
- P0117, p0118 ect sensor
- P0122, P0123 TP Sensor
- P0125 ECT Sensor
- P0127 IAT Sensor
- P0128 Thermostat function
- P0130 A/F Sensor 1
- P0131 A/F Sensor 1
- P0132 A/F Sensor 1
- P0133 A/F Sensor 1
- P0137 HO2S2
- P0138 HO2S2
- P0139 HO2S2
- P0171 fuel injection system function
- P0172 fuel injection system function
- P0181 FTT Sensor
- P0182, P0183 FTT Sensor
- P0222, P0223 TP Sensor
- P0300, P0301, P0302, P0303, P0304 Misfire
- P0327, P0328 KS
- P0335 CKP Sensor (POS)
- P0340 CMP Sensor (phase)
- P0420 three way catalyst function
- P0441 evap control system
- P0442 evap control system
- P0443 evap canister purge volume control solenoid valve
- P0444, p0445 evap canister purge volume control solenoid valve
- P0447 evap canister vent control valve
- P0448 evap canister vent control valve
- P0451 evap control system pressure sensor
- P0452 evap control system pressure sensor
- P0453 evap control system pressure sensor
- P0455 evap control system
- P0456 evap control system
- P0460 fuel level sensor
- P0461 fuel level sensor
- P0462, p0463 fuel level sensor
- P0500 VSS
- P0506 ISC System
- P0507 ISC System
- P0550 PSP Sensor
- P0603 ECM Power supply
- P0605 ECM
- P0607 ECM
- P0643 sensor power supply
- P0850 PNP Switch
- P1148 closed loop control
- P1217 engine over temperature
- P1225 TP Sensor
- P1226 TP Sensor
- P1421 cold start control
- P1550 battery current sensor
- P1551, P1552 Battery current sensor
- P1553 battery current sensor
- P1554 battery current sensor
- P1564 ASCD Steering switch
- P1572 ASCD Brake switch
- P1574 ASCD Vehicle speed sensor
- P1715 input speed sensor (primary speed sensor)
- P1805 brake switch
- P2100, p2103 throttle control motor relay
- P2101 electric throttle control function
- P2118 throttle control motor
- P2119 electric throttle control actuator
- P2122, P2123 APP Sensor
- P2127, P2128 APP Sensor
- P2135 TP Sensor
- P2138 APP Sensor
- P2A00 A/F Sensor 1
- ASCD Brake switch
- ASCD Indicator
- Cooling fan
- Electrical load signal
- Fuel injector
- Fuel pump
- Ignition signal
- Malfunction indicator lamp
- On board refueling vapor recovery (ORVR)
- Positive crankcase ventilation
- Refrigerant pressure sensor
On board diagnostic (OBD) System
Diagnosis Description INTRODUCTION The ECM has an on board diagnostic system, which detects malfunctions related to engine sensors or actuators. The ECM also records various emission-related di ...Trouble diagnosis - specification value
Description The specification (SP) value indicates the tolerance of the value that is displayed in “SPEC” of “DATA MONITOR” mode of CONSULT-III during normal operation of the Engine Contr ...Other materials:
Basic inspection
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
OVERALL SEQUENCE
DETAILED FLOW
NOTE:
To ensure a complete and thorough diagnosis, the battery, starter motor and
alternator test segments must be
done as a set from start to finish.
1.DIAGNOSIS WITH STARTING/CHARGING SYSTEM TESTER
Perform the start ...
Auto operation does not operate but manual operates normally
(driver side)
Diagnosis Procedure
1. PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
Refer to PWC-295, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special
Repair Requirement".
Is the inspection result normal?
YES >> GO TO 2
NO >> Repair or replace the ma ...
P2118 Throttle control motor
Description
The throttle control motor is operated by the ECM and it opens and closes the
throttle valve.
The current opening angle of the throttle valve is detected by the throttle
position sensor. The throttle position
sensor it provides feedback to the ECM, when opens/closes the throttle ...